Any time your LG dryer is having an issue of some kind, it\u2019s smart enough to know where most of the problems stem from. And when it detects one, you\u2019ll get an error code on its display.<\/p>\n
LG has a number of different error codes that call into question specific problems such as a blocked exhaust vent or not enough water for a steam cycle.<\/p>\n
Dryers are very sensitive to the amount of voltage being supplied to it. When there\u2019s too little\u2014less than 240 volts\u2014then the dryer cannot perform all the functions necessary. The error code \u201cnP\u201d indicates that there\u2019s an electrical problem somewhere. It\u2019s less likely that it\u2019s the dryer, and far more likely that it\u2019s your home.<\/p>\n
Start by checking the power cable\u2019s position. Is it plugged directly into an electrical outlet or do you have it plugged into an extension cord or power strip?<\/p>\n
If you do, it\u2019s a dead giveaway. A power strip or extension cable is reducing the amount of volts the dryer needs. Plug directly into an electrical outlet. While you\u2019re at it, inspect your electrical outlets for any damage like burns.<\/p>\n
There may have been a power surge recently. Reset the circuit breaker. Turn it off and wait 10 seconds, then back on. That should give it enough time to reset. Of course, if that doesn\u2019t help, then a repair might be necessary.<\/p>\n
The exhaust system is really sensitive to clogs. If it\u2019s blocked in some way, then the hot, humid air that the clothing is producing from drying cannot escape in a quick enough fashion.<\/p>\n
When that happens, you\u2019ll get an error. If the exhaust is clogged as much as 75 percent, your dryer starts to display the \u201cd75\u201d error, accompanied by the Flow Sense displaying two to four bars.<\/p>\n
At 80 percent, it\u2019s error code \u201cd80.\u201d At 90 percent, it’s the error code \u201cd90.\u201d Lastly, d95 is when the humidity reaches 95 percent.<\/p>\n
The source of the problem is linked to damage of the exhaust system or a buildup of some kind in the exhaust itself. Additionally, the exhaust should be adequately positioned with as few bends as possible, and as short as possible.<\/p>\n
On the other side of the spectrum, if you see error code \u201cPS,\u201d then it indicates there\u2019s something wrong with the power cable itself. Not enough voltage is being delivered to the power cable.<\/p>\n
However, it\u2019s more than likely that the red and white wire connections on the terminal block were swapped by accident. This issue can be fixed by switching the placement of the red and white wire connections.<\/p>\n
A \u201cdE\u201d error code simply means the door isn\u2019t closed. All you have to do is open it up and check that everything is in order such as the lint filter, the lock itself and the alignment of the door. In the event that the error code returns, shut the unit down, boot it back up and give it another try, but this time around firmly close the door.<\/p>\n
Error code \u201cE13\u201d directly relates to the drain hose. It can be very sensitive to kinks, crushing, clogs, or freezing. In the event that any one of those affect the drain hose, you get error code \u201cE13.\u201d<\/p>\n
Like the exhaust system, you don\u2019t want unnecessary length added to the drain hose. If there\u2019s an extension added, that\u2019s more for the water to travel. Reduce the length of the drain hose if you can.<\/p>\n
The lint filter can only sit correctly one way, and when it isn\u2019t you get error code \u201cFO.\u201d Remove the filter and seat it into the slot so that it matches the curve of the dryer. It should NOT be sticking out at any weird angles.<\/p>\n
There\u2019s humidity sensors located on the other side of the filters, sensors that appear to be metal exposed along the filter. If they\u2019re dirty, they can cause the \u201cHS\u201d error code, but more importantly it can run the dryer for over two hours. Clean them off and let the sensors dry before using the dryer again.<\/p>\n
Error code \u201cPF\u201d typically happens when you\u2019ve experienced a power outage, even a brief one. All you have to do is reset the dryer. You do that by unplugging the unit, holding the Start\/Pause button for five seconds, then powering it back on.<\/p>\n
Error codes \u201ctE1,\u201d \u201ctE2, and \u201ctE3\u201d all relate to the thermistor. The circuit board takes orders from the thermistor and uses the temperature information the thermistor has to determine whether or not the heating element should be used.<\/p>\n
This one is simple: your dryer isn\u2019t getting any gas. Check that the gas link is damaged or kinked. Additionally, the supply valve should be turned on.<\/p>\n
\u201cCL\u201d isn\u2019t an error code persay, but rather an indicator that the child lock has been enabled. It\u2019s to prevent children from messing with the settings. Disable it by holding the Child Lock button for three seconds.<\/p>\n
When you get the error code \u201cAdd,\u201d it means there\u2019s something wrong with your water supply for use with the steam cycle, for example. Simply add water.<\/p>\n","protected":false},"excerpt":{"rendered":"
Any time your LG dryer is having an issue of some kind, it\u2019s smart enough to know where most of the problems stem from. And when it detects one, you\u2019ll get an error code on its display. LG has a number of different error codes that call into question specific problems such as a blocked […]<\/p>\n","protected":false},"author":2,"featured_media":259,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_lmt_disableupdate":"no","_lmt_disable":"","footnotes":""},"categories":[13],"tags":[],"yoast_head":"\n