Despite their good quality products, users still experience issues with the whirlpool Cabrio washer, as they do with any other good quality appliance.
This piece will help you troubleshoot some of the common Whirlpool Cabrio washing machines and restore them back to their optimum efficiency.
Common Whirlpool Cabrio Washer Issues and Fixes
There are common whirlpool problems that most users experience. Fortunately, these faults are easy to fix.
Washer Creating Unusual Noises
This problem is marked by loud noises coming from the washing machine. These noises are in different forms.
The noise can be a loud thumping sound meaning that your washer has an unbalanced load. Fix this problem by stopping the cycle and redistributing wet laundry. You would have to get rid of some clothes if your washing machine was overloaded.
If it was a clanging noise, your washing machine might not be leveled or fixed to the floor. You need to fix this issue by grounding your washing to the floor to stop any more damage.
When your washer produces a high-pitched whine, you have to conduct extensive research to determine the exact cause of the noise.
Use your owner’s manual to know how to navigate the internal parts of your washing machine. You can also get a repair manual on the whirlpool site that you can use for the same cause.
Remove your washer’s outer housing and inspect the nuts holding the pulley in place. You might have to tighten the nuts. It this solution does not work; you will have to replace your washer’s bearings.
Lid Lock Problems
This problem occurs when your washer’s lid lock but unlocks hence stopping the start of a new cycle.
Your washer’s lid switch/latch does not engage when it is dirty. Dirt prevents the latch from making proper contact to prompt your washing machine to start a new cycle. Use a cotton swab dipped in isopropyl rubbing alcohol to clean every contact area on your washing machine’s lid.
You can also unplug your washer from its power source to reset the control panel of the washing machine. Connect your washing machine back to its wall socket to examine if the problem has been resolved.
If your washer’s door produces a sound similar to what it makes when engaging but does not engage, you need to conduct a full diagnosis on the appliance. The washing machine might have a bigger problem. Use this procedure to run the test:
Put your washing machine on standby mode. To achieve this, you need to plug the washer into its power socket and turn off all its indicators. However, you can leave the clothes done or clean indicator on. Choose any button other than Start, Power, or Stop and follow the steps listed below using your button of choice.
- Press the button down for three seconds
- Release the button for three seconds
- Hold the button, again for three seconds
- Release the button, again for three seconds
- Press it one last time for three seconds
- Release it for the last time
All the indicators in your washing machine’s console will light up for at least five seconds. Eighty-eight of these indicators will show, in their estimated time remaining, a two-digit display showing that your washer’s diagnostic mode has been successfully entered.
If your washer’s indicator fails to display as explained above, then the press and release process may not have been performed inside the required timeframe for successful entry. Repeat this procedure using a different button to ensure that the button used earlier was not the reason for the failure.
Your washer’s program will look for saved error codes. Once the diagnostic test is complete, you may choose to compare your washer’s fault code displayed to know the exact repairs needed to be done on your washing machine.
Washer Won’t Start
This problem mostly results from a faulty start button on your washer’s control panel. The start button is not working, but the rest of the lights in your washer turn on. Follow these steps to troubleshoot and fix your washing machine.
Remove your washer’s control panel to conduct a diagnosis on your appliance. You need to use your repair manual when removing the control panel to ensure you follow the right steps.
Examine the panel for any broken or loose pieces. In some cases, small plastic pieces break off behind your washer’s start button and hinder it from powering.
Use a voltage meter (view on Amazon) to examine all the wiring in the control panel. Sadly, if the main controller/CCU or timer fails, the entire control panel of your washing machine should be replaced.
Breaking Down the LD Error Code
An LD code shows on the display screen in the course of a spin cycle. This error code indicates a long drain.
When the LD code shows, your washing machine stops running. When this error code shows on your washing machine’s display, then your appliance’s drain line might be clogged. It might also indicate an obstruction in your washer’s pump. Correct this problem using these steps.
Clean any obstruction or lint that might be clogging your pump filter.
Switch off your washer’s water connection and unhook your appliance’s drain line from it’s the main washer. Keep a bucket close to trap any spill. Finally, clean the line by forcefully streaming water through it or by using a long brush.
If these solutions to not fix your washer and restore it back to its optimum efficiency, you may need to replace the water pump.
Washing Machine Produces a Burning Plastic Odor
You will know that this problem exists when your washer produces a smell of burning rubber or plastic.
When your washer emits this smell, you need to take immediate action. Begin by unplugging the washing machine from its power source and open its outer housing.
Search for discoloration. There is a possibility that your washer’s rubber drive belt (view on Amazon) is faulty. If this belt slips, breaks or stretches, it can lead to friction and produce a burning smell. In most cases, it is a smell of burning rubber. You should replace the belt.
If your washer’s belt shows no sign of weakness, the appliance might have an electrical issue, especially with its transmission, control panel, or motor.
If this is the case, you might have to seek the services of an appliance specialist since this is a more advanced problem. You will have to replace all the damaged parts of the washer.
Avoid using the washer until you repair all the damaged parts of your washer.
Washer Leaves Deposits on Dark Clothes
This problem often occurs on washers even when you change detergents.
If your washer leaves the deposits in winter, it might be as a result of incomplete dissolving of powder detergents because of the extremely cold water temperatures. Switch your washer to warm water temperature cycles.
If the frequency in which these deposits occur increases, you should clean your washing machine.
One of the disadvantages of using high-efficiency washing machines versus using a standard machine is that you will not have to use large amounts of water to flush detergents from your washer and soil residue, which ends up clinging to your washing machine.
Therefore, you need to clean your washer to remove the accumulation, which is redepositing on your clothes.
Rust Patches on the Lid of Your Washing Machine
This problem presents itself as rust patches in the inner parts of your Cabrio washer lid.
Rust patches on the lid never disappear. They only grow in size unless you fix them. They may also transfer rust stains on to your clothes. Using distilled white vinegar and a paste of baking soda, remove as much of the rust growing on your appliance as possible.
You can also use lemon juice in place of distilled white vinegar. Mix enough lemon juice or distilled white vinegar with one-quarter cup of baking soda to make a very thick paste.
Apply the paste over the rusted lid area. Use a soft piece of cloth to remove all the loose rust particles from the lid. Repeat this process severally as you rinse the area using clean water after each rub or treatment.
Immediately all the loose rust particles are removed fix the rusted area using appliance paint according to the product directions.
Other than these issues, there are some problems that may arise due to the use of the wrong products. Therefore, you need to use only the right soap, in this case, the high efficiency (HE) soap.
Even though this soap is expensive, it will help you get clean clothes out of every spin cycle. When you do not use HE soap, you risk getting clothes that are not satisfactorily clean, bad tab bearings, and error codes showing on your washer’s display screen.
Fortunately, Whirlpool Cabrio washer has a self-diagnostic mechanism which shows error codes on its display screen. These error codes correspond to specific faults within your washer.
Therefore, you can fix the issue as a DIY project purely based on the description of your owner’s manual about the error code. Some of the most common error codes include:
LF error code (F30) – Long Fill
LF shows on your washer’s display screen when the levels of water do not change over a given period after all the valves are switched on or when water is released from the drum, but the washing machine’s control panel fails to detect the change in water level.
When this happens, you need to inspect the connection of your water supply and ensure it is switched on.
You also need to ensure the screens are correctly plugged in. Lastly, if the water is flowing into your washer’s tub, inspect the appliance’s pressure hose connection to the motor control.
oL error code (F70) – Overloaded
The oL error code shows on your washing machine’s display screen when the appliance’s motor control detects a heavier than expected load size.
Correct this problem by opening the lid of your washing machine and remove excess clothes from the appliance. Restart the appliance and observe if it works as expected.
These are the common problems that you will experience with the Whirlpool Cabrio washing machine. These problems can be diagnosed and fixed easily using your owner’s manual and a keen eye to detail.
However, if you do not feel comfortable working on your appliance, call an appliance repair technician to troubleshoot and fix your washer. Always remember to take all the necessary precautionary measures when working with electrical appliances.
